金属表面涂装行业VOCs排放特征及排放系数

对比了浙江省2014和2018年金属表面涂装企业的有机废气排放及治理情况,分析了该行业涂料及稀释剂的使用、主要污染因子,测算了溶剂型、水性涂料的挥发性有机物（VOCs）产生系数和排放系数.结果表明：2018年VOCs治理水平明显高于2014年,水性涂料使用企业比例由18%上升至36%,纯溶剂型企业由82%下降至64%;金属表面涂装行业的主要排放污染物为二甲苯、丁醇、乙酸乙酯、乙酸丁酯、甲苯、丙二醇、乙苯、苯乙烯等8种有机物.溶剂型和水性涂料的VOCs产生系数分别为0.72和0.31kg/kg;溶剂型和水性涂料2014年VOCs排放系数为0.64和0.29kg/kg,2018年为0.48和0.21kg/kg.     

Regulated emission characteristics of in-use LNG and diesel semi-trailer towing vehicles under real driving conditions using PEMS

On-road driving emissions of six liquefied natural gas(LNG) and diesel semi-trailer towing vehicles(STTVs) which met China Emission Standard IV and V were tested using Portable Emission Measurement System(PEMS) in northern China.Emission characteristics of these vehicles under real driving conditions were analyzed and proved that on-road emissions of heavy-duty vehicles(HDVs) were underestimated in the past.There were large differences among LNG and diesel vehicles, which also existed between China V vehicles and China IV vehicles.Emission factors showed the highest level under real driving conditions, which probably be caused by frequent acceleration, deceleration, and start-stop.NOx emission factors ranged from 2.855 to 20.939 g/km based on distance-traveled and 6.719–90.557 g/kg based on fuel consumption during whole tests, which were much higher than previous researches on chassis dynamometer.It was inferred from tests that the fuel consumption rate of the test vehicles had a strong correlation with NOx emission, and the exhaust temperature also affected the efficiency of Selected Catalytic Reduction(SCR) aftertreatment system, thus changing the NOx emission greatly.THC emission factors of LNG vehicles were 2.012–10.636 g/km, which were much higher than that of diesel vehicles(0.029–0.185 g/km).Unburned CH_4 may be an important reason for this phenomenon.Further on-road emission tests, especially CH_4 emission test should be carried out in subsequent research.In addition, the Particulate Number(PN) emission factors of diesel vehicles were at a very high level during whole tests, and Diesel Particulate Filter(DPF)should be installed to reduce PN emission.     

Chemical characteristics of road dust PM2.5 fraction in oasis cities at the margin of Tarim Basin

In order to understand the compositions characteristics of particulate matter with aerodynamic diameter less than 2.5 μm (PM_2.5) fraction in road dust (RD_2.5) of oasis cities on the edge of Tarim Basin, 30 road dust (RD) samples were collected in Kashi, Cele, and Yutian in the spring, 2018, and RD_2.5 was collected using the resuspension approach. Eight water-soluble ions, 39 trace elements and 8 fractions of carbon-containing species in PM_2.5 were analyzed. Ca²⁺ and Ca were the most abundant ions and elements in RD_2.5 (7.1% and 9.5%). Cl^- in RD_2.5 was affected not only by attributed to saline-alkali soils in oasis cities of the Tarim Basin and dust from Taklimakan Desert but also by human activities. Moreover, the organic carbon/elemental carbon (OC/EC) ratio indicated that carbon components in RD_2.5 in Cele town mainly come from fossil fuel combustion, while those in Yutian and Kashi mainly come from biomass combustion. It is noteworthy that high Ca in RD_2.5 was seriously affected by anthropogenic emissions, and high Na and K contents in RD_2.5 could be derived from soil and desert dust. It was estimated that Cd, Tl, Sn and Cr were emitted from anthropogenic emissions using the enrichment factor. The coefficients of divergence (COD) result indicated that the influence of local emission on road dust emission is greater than that of long-distance transmission. This study is the first time to comprehensively analyze the chemical characteristics of road dust in oasis cities, and the results provides the sources of road dust at the margin of Tarim Basin.     

Investigation to meet China II emission legislation for marine diesel engine with diesel methanol compound combustion technology

In order to reduce the pollutant emission and alleviate the pressure of petroleum resources shortage and greenhouse gas emission at the same time, the use of clean and renewable alternative fuel for marine engines is a promising option. In this study, a marine diesel engine, which was modified to run in diesel methanol compound combustion (DMCC) mode, was investigated. After the diesel injection parameters were calibrated, and combined with a sample after-treatment device DOC (diesel oxidation catalyst), the engine could meet the requirements of China II legislation. The overall MSP (methanol substitute percent) reached 54.1%. The value of each pollutant emission was much lower than that in China II emission legislation, and there was almost no methanol and formaldehyde emissions. When methanol was injected into the inlet manifold, the intake air temperature decreased a lot, as well as the exhaust gas temperature, which were beneficial to increase engine thermal efficiency and improve engine room environment. Compared with the engine running in pure diesel mode, when the engine ran in diesel/methanol dual fuel mode, the combustion phase was advanced, and the combustion duration became shorter. Therefore, the engine thermal efficiency increased, and fuel consumption decreased significantly.     

Reviews of emission of biogenic volatile organic compounds (BVOCs) in Asia

Biogenic volatile organic compounds (BVOCs) in the atmosphere play important roles in the formation of ground-level ozone and secondary organic aerosol (SOA) in global scale and also in regional scale under some condition due to their large amount and relatively higher reactivity. In places with high plant cover in the tropics and in China where air pollution is serious, the effect of BVOCs on ozone and secondary organic aerosols is strong. The present research aims to provide a comprehensive review about the emission rate, emission inventory, research methods, the influencing factors of BVOCs emissions, as well as their impacts on atmospheric environment quality and human health in recent years in Asia based on the summary and analysis of literatures. It is suggested to use field direct measurement method to obtain the emission rate and model method to calculate the emission amount. Several recommendations are given for future investigation and policy development on BVOCs emission.     

达里诺尔湖水体DOM荧光特征及其来源解析

达里诺尔湖（简称“达里湖”）是内蒙古自治区高原地区重要的生态屏障,探究达里湖水质状况及污染来源,对加强流域水环境治理、改善水环境质量具有十分重要的意义.于2018年9月及2019年6月对湖水进行采样,并通过三维荧光光谱结合PARAFAC（平行因子分析）模型,探究达里湖水体DOM（溶解性有机质）来源及其与水质的关系.结果表明:①达里湖水体中pH较高,ρ（DOC）（DOC为溶解性有机碳）、ρ（NH₄+-N）、ρ（TP）相对较高,均超过GB 3838—2002《地表水环境质量标准》Ⅴ类水质标准限值.②水体中DOM含4种荧光组分.夏季水体DOM主要分布于河流入湖口附近,其中,类腐殖质荧光组分（紫外区类富里酸和可见区类富里酸）占总组分的62.93%,类蛋白类荧光组分（类色氨酸和类酪氨酸）占总组分的36.07%;秋季水体DOM主要分布于东南侧,其中,类腐殖质荧光组分占总组分的40.52%,类蛋白类荧光组分占总组分的59.48%.③达里湖采样点荧光参数表明,达里湖DOM自生源特征较强,腐殖化程度较低.类腐殖质荧光组分与ρ（DOC）、ρ（Chla）均呈正相关,类色氨酸荧光组分与pH呈正相关,类络氨酸与ρ（DTN）、ρ（NH4+-N）、ρ（DTP）均呈正相关.研究显示,达里湖DOM具有陆源与生物源双重特性,DOM的形成与微生物、细菌、浮游生物的生命活动密切相关.      

随机振动响应峰值因子的预计理论研究

简要介绍了超越概率理论、超越频次理论、损伤等效理论和功率谱密度(PSD)的时域拟合理论等4种常见的峰值因子预计理论,并基于三角级数提出了一种新的预计理论。结合试飞加速度数据样本,对比分析超越频次理论、PSD时域拟合理论和三角级数理论的预估精度。研究表明,上述4种常见的预计理论本质上属于统计学理论;PSD时域拟合理论预计的峰值因子波动较大,峰值因子与归一化次数满足高斯分布;三角级数理论的预估精度较高,但缺乏离散峰个数的合理判据。     

黄土塬面保护区潜在蒸发量时空变化及其与气象、环流因子关系分析

黄土塬面是黄土高原地区主要的农业分布区和人口聚居地,地位十分重要。黄土塬面潜在蒸发量（ET₀）的研究对于区域水循环研究、水土流失防治及农业的可持续发展具有重要意义。基于黄土塬面保护区1960—2017年的气象数据,利用Penman-Monteith模型、小波分析、Mann-Kendall非参数检验等方法研究了黄土塬面保护区ET₀的变化规律及其与气象、环流因子间的关系。结果表明：（1）黄土塬面保护区多年平均ET₀为1173.4 mm,总体呈现增长趋势,增长率为21.1 mm/10 a;其生长季平均ET₀值及增长率均高于非生长季平均ET₀。（2）该区多年平均ET₀空间分布特征表现为东部高西部低,西部甘肃塬区多年平均ET₀远低于东部山西塬区。（3）过去58年来,区域年均、生长季、非生长季ET₀均呈现出增长趋势,但空间差异明显;研究区年均ET₀存在着10年、30年和50年的震荡周期,其中以30年周期为主周期。（4）气温是控制区域ET₀变化的最重要的气象因子,但气温对ET₀的影响具有明显的空间差异,在整个研究区内最低气温影响最显著;而甘肃塬区和陕西塬区的ET₀变化主要受平均气温变化的控制,在山西塬区最高气温的变化是区域ET₀变化的主要控制因子。（5）遥相关分析结果显示太平洋/北美指数（PNA）与北大西洋年代尺度振荡（AMO）对该区域ET₀变化有一定影响,西太平洋海温指数（WPI）的变化影响区域非生长季ET₀变化。     

京津冀西北典型区域地下水位时空演变及驱动因素

京津冀西北地区是北京、天津重要的水源涵养区和生态屏障,也是“京津冀协同发展”战略重要的支撑区域。为揭示京津冀西北地区地下水位时空演变规律及其驱动因素,以张家口地区为研究区域,选取1981—2015年56个地下水位观测井连续观测数据、水文地质相关资料、气象数据、地下水资源开采数据和社会经济数据,对研究区内坝上高原、柴宣盆地、涿怀盆地和蔚阳盆地四个地貌单元地下水位时空演变规律和驱动因素进行分析。结果表明：张家口地区四个地貌单元及下辖各区县地下水位呈整体下降趋势,且下降速率逐步加快。35年间坝上高原水位降幅3.59 m<蔚阳盆地水位降幅3.6 m<涿怀盆地水位降幅7.17 m<柴宣盆地水位降幅20.41 m。张家口地区四个地貌单元地下水位动态变化与降雨量、蒸发量、气温等自然因素相关性较差,但与第一产业产值、常用耕地面积、有效灌溉面积、粮食总产量、蔬菜总产量、猪牛羊肉总产量、第二产业产值、第三产业产值和年末总人口等社会经济因素存在显著的相关性。在主成分分析中四个地貌单元前两个主成分的累计方差贡献率均>80%,其中第一个主成分主要为蔬菜总产量、猪牛羊肉总产量、年末总人口和第一、第二、第三产业产值等社会经济因素,不同地貌单元均可解释66%以上,表明社会经济因素是造成张家口地区地下水位持续下降的主要驱动因素。研究成果可为该地区未来社会经济的可持续发展和区域水资源的合理利用、调配以及京津冀西北地区水源涵养和生态功能保持提供理论依据。     

河北坝上与坝下不同土地利用类型土壤入渗特征及其影响因素

为查明河北省坝上与坝下不同土地利用类型土壤入渗能力,选择张北县（坝上风蚀区）和阳原县（坝下水蚀区）作为典型研究区,采用微型圆盘入渗仪测量土壤入渗特性,并分析其主要影响因素。研究结果表明：（1）阳原县不同土地利用类型土壤渗透性能表现为：高盖度草地>低盖度草地>耕地>林地,张北县表现为：草地>耕地>灌木林地>防护林地;（2）不同入渗模型拟合度之间存在显著差异,其中Philip模型拟合效果最佳;（3）土壤初始入渗速率、稳定入渗速率、稳定入渗时间与容重呈极显著负相关关系,而与总孔隙度均呈极显著正相关关系。结果表明,该区草地土壤入渗能力最强,后期开展生态工程建设时应更加重视草地涵养水源的作用。